LISTEN 10:18

The brand-new McLaren 650S was introduced at the 2014 Geneva Motor Show as a replacement for the MP4-12C. The sports car debuted in Coupe and Roadster body styles with 640 horsepower and 500 pound-feet of torque on tap. Powered by the same twin-turbo, 3.8-liter V-8 seen across the entire McLaren lineup, the 650S comes to the market as a competitor for the Ferrari 458 and the Lamborghini Huracan. Coming into 2015, the British sports car is also getting a track suit with a 650S GT3 label on it.

Developed as a successor to the highly acclaimed 12C GT3, the 650S will replace its forerunner in the Blancplain Endurance Series starting next year. Additionally, the new race car will get to showcase its skills in various GT races around the world hoping to match the success of its predecessor. Although it is essentially an updated 12C GT3, the 650S GT3 carries an array of newly-developed racing parts, which are supposed to make it faster and more agile on the track. Only time will tell if the 650S is worthy of the GT3 moniker, but, until then, let’s have a look at the technology behind it.

Updated 07/27/2015: The McLaren 650S GT3 finished honorably in its most demanding test to date this weekend: two entered entered the Total 24 Hours of Spa and both claimed top 10 finishes. McLaren dropped a very nice picture gallery from the race, so enjoy!

Click past the jump to read more about the 2015 McLaren 650S GT3.

  • 2015 McLaren 650S GT3
  • Year:
  • Make:
  • Model:
  • Engine:
  • Horsepower @ RPM:
  • Displacement:
    3.8 L
  • 0-60 time:
    2.9 sec.
  • Top Speed:
    207 mph
  • Price:
  • Price:
  • car segment:
  • body style:


2015 McLaren 650S GT3 High Resolution Exterior
- image 557796
2015 McLaren 650S GT3 High Resolution Exterior
- image 557798
2015 McLaren 650S GT3 High Resolution Exterior
- image 557800

Just as the road-legal McLaren 650S is a successor to the MP4-12C, which was discontinued earlier this year, the 650S GT3 is an evolution of the 12C GT3. Built with motorsport in mind, the 650S GT3 is a more radical version of the standard 650S, with tons of race-specific gear added inside and out.

The revised front hood provides additional cooling to the car's internals, while the wider front fenders further enhance the GT3 menacing stance.

Up front, the GT3 is distinguished by a large carbon-fiber splitter and enhanced air intakes on each side of the nose. The revised front hood provides additional cooling to the car’s internals, while the wider front fenders further enhance the GT3 menacing stance. Moving toward the rear, reshaped side air intakes are in place to send even more air into the engine, while the redesigned side sills make sure the racer remains planted at high speeds.

Around back, a huge, fixed carbon-fiber wing provides the necessary downforce and optimum airflow over and around the GT3. The 650S’ traditional rear bumper has been replaced by a track-spec diffuser that hangs closer to the ground. The aerodynamic piece is quite aggressive by design and represents a major improvement compared to the 12C GT3.

Naturally, the 650S GT3’s body is made entirely of carbon-fiber, with panel design and fit optimized to minimize pit lane repair times. The body is lighter than ever before and sits on a two-inch-wider track.


Driver safety is one of the key areas McLaren focused while developing the 650S GT3. Protection offered by the revised carbon-fiber MonoCell chassis is enhanced with the addition of a brand-new, FIA-approved roll cage that’s lighter than that of the 12C GT3. The new roll cage provides increased leg and headroom, which will translate into a greater degree of driver comfort during those long endurance events.

The dash sits behind the vehicle's unique steering wheel, which borrows the design seen in McLaren's Formula 1 car.

Speaking of comfort, drivers will also benefit from an all-new race seat developed by the company’s GT division. Fitted with a six-point race harness as standard, the seat offers increased levels of support by means of bespoke molded inserts. The seat is built to FIA standards and mounted to the chassis.

Assisting the drivers throughout the races is a digital dash displaying all sorts of vital parameters, including speed and fuel consumption. The dash sits behind the vehicle’s unique steering wheel, which borrows the design seen in McLaren’s Formula 1 car. An all-new, adjustable, motorsport pedal box and a membrane-type switch panel round off the track-ready cockpit.


2015 McLaren 650S GT3 High Resolution Exterior
- image 557789

The 650S GT3 is motivated by McLaren’s familiar twin-turbo, 3.8-liter, V-8 engine. The unit carries the same configuration as in the 12C GT3, meaning it benefits from the same 493-horsepower rating controlled by FIA regulations. However, the 650S features an all-new, six-speed sequential transmission with improved shifting and an oil cooler incorporated into the large side intakes. Engine cooling is improved, thanks to the larger intakes cut into the front bumper. All told, expect the 650S GT3 to be slightly faster that the already successful 12C GT3.

2015 McLaren 650S GT3: Drivetrain Specification

Engine Race prepared 3.8L V8 twin turbo McLaren M838T
Managements McLaren Electronics ECU incorporating turbo boost and transmission shift control
Transmission Six-speed sequential motorsport transmission pneumatically actuated via steering wheel mounted paddles
Output 493 HP


2015 McLaren 650S GT3 High Resolution Exterior
- image 557788

Helping the 650S GT3 on the race track is an all-new, race-tuned suspension system, a two-inch-wider track, and new-generation, larger racing tires. Aided by the revised aerodynamic package, the combo provides increased levels of grip and steering feel on turn-in. The new tires wrap around brand-new, forged-aluminum wheels measuring 18 inches at all corners. Stopping power is provided by a revised braking system consisting of ventilated discs and monoblock calipers. Up front, the 380-by-35-mm (15-by-1.4-inch) discs mate to six-piston calipers, while the rear, 355-by-32-mm (14-by-1.3-inch) discs are paired to four-piston calipers.


Only 15 examples of the 650S GT3 will be built and sold for £330,000 each before taxes, which means around $562,000 as of 06/27/2014. Deliveries will commence in late 2014, just in time for customers to start testing before the 2015 motorsport season commences.

Additionally, privateers that already own the 12C GT3 will be able to opt for an upgrade package that basically transforms this year’s race car into a 650S GT3. About 15 such packages will be sold, but McLaren has yet to announce pricing information.


Audi R8 LMS Ultra

2014 Audi R8 LMS ultra High Resolution Exterior Wallpaper quality
- image 547738

The Audi R8 LMS Ultra is McLaren’s main rival for the 2015 Blancpain Endurance Series. The German race car is based on the production, road-legal Audi R8 and features a bevy of racing upgrades to make it viable for endurance events. Setting it apart from the road-going R8 is a revised hood, a front bumper spoiler, new side sills, a larger rear wing and a race-specific rear diffuser.

A track-ready suspension system and more efficient brakes are also part of the package. Behind the seats lies Audi’s familiar 5.2-liter, V-10 engine, with certain updates added to increase its potential. Output sits at 562 horsepower, 12 ponies more than the road-legal R8 V-10 Plus. Power is routed to the rear wheels by a six-speed sequential gearbox operated by paddle shifters mounted behind the steering wheel.

Bentley Continental GT3

2014 Bentley Continental GT3-R High Resolution Exterior
- image 556253

Based on the production Bentley Continental GT, the GT3 is a fresh entry into the Blancpain Endurance Series. Introduced for the 2014 season, the British machine laps the tracks by means of 4.0-liter, V-8 engine that generates 600 twin-turbocharged horses. Sending power to the ground is a six-speed sequential transaxle gearbox using a racing clutch and a limited-slip differential.

Stripped of all the luxury features found in the regular Continental GT and fitted with several carbon-fiber parts inside and out, the GT3 tips the scale at only 2,866 pounds.


2015 McLaren 650S GT3 High Resolution Exterior
- image 557791

The 650S GT3 comes to replace a very successful 12C GT3. As of June 2014, the latter has three championship titles and 51 race wins to its name, making it the winningest McLaren of the modern era. Improving on such success won’t be an easy task, but the 650S comes with many chassis and aerodynamic improvements that are bound to make it faster and more agile. We know race cars are developed to be quick rather than beautiful, but the 650S GT3 is one of those track rockets that manages to be both.

  • Leave it
    • No additional horsepower
    • We won’t see it in action until 2015

Updated History

Updated 10/06/2014: McLaren announced that its new 650S GT3 is about to face toughest test yet with 12 hour desert endurance test set to take place the Yas Marina Circuit in Abu Dhabi, 12-13 December. After this final race, the 650S GT3 will join customer teams from next season.

Ciprian Florea
Ciprian Florea
Senior Editor and Supercar Expert -
Ciprian's passion for everything with four wheels (and more) started back when he was just a little boy, and the Lamborghini Countach was still the coolest car poster you could hang on your wall. Ciprian's career as a journalist began long before earning a Bachelor's degree, but it was only after graduating that his love for cars became a profession.  Read full bio
About the author

Press Release

In the grounds of the famous Goodwood Estate, McLaren GT has today confirmed first details of the McLaren 650S GT3 – the latest generation track-focused racer which will contest GT3 championships across the globe from the 2015 season. Building on the highly successful 12C GT3, which has firmly re-established McLaren at the front of the GT grid over the past three seasons, the 650S GT3 was unveiled in front of fans and the global motorsport media at the 2014 Goodwood Festival of Speed.

2015 McLaren 650S GT3 High Resolution Exterior
- image 557787

As the 12C GT3 continues claiming trophies around the world, the 650S GT3 has big shoes to fill, but it has been designed to do just that. The menacing and purposeful-looking racer is the second-generation GT3 car from McLaren GT, the GT race car building arm of McLaren, and follows in the slipstream of the 12C GT3, now competing in its third competitive season. To date, the 12C GT3 has secured three championship titles, 51 race victories and 71 further podiums, a number that continues to rise on a weekly basis, and currently leads the highly competitive Blancpain Endurance Series and the GT Asia championship.

Based on the recently unveiled McLaren 650S, and built around the same lightweight carbon fibre MonoCell chassis, the GT3 iteration has been honed using CFD technology and the latest in automotive and motorsport simulation to offer enhanced aerodynamics and improved levels of cooling. At the front, an aggressive splitter and larger air intakes dominate the purposeful new look, incorporating the familiar McLaren ‘face’ – albeit a more aggressive and menacing version, while on the flanks, the all-new lightweight carbon fibre bodywork wraps around reprofiled air intakes, which offer further optimised cooling. The fixed carbon fibre rear wing works in tandem with the large carbon fibre splitter to complete the management of air as it is worked across, through and beneath the sleek lines of the 650S GT3.

The road-going version has been designed and developed to provide ‘the ultimate in driver engagement on the road’, and the 650S GT3 uses this same approach. Revised suspension geometry, wider track and updates to the overall setup provide enhanced levels of drivability, optimising engagement for the wide range of drivers competing in GT racing. In addition, the updates have been made with added emphasis on endurance racing, pulling from the learnings over the past few years, and responding to feedback from the customer teams.

2015 McLaren 650S GT3 High Resolution Exterior
- image 557788

Reduced cost of ownership has been a priority during the design and development of the 650S GT3, and this has been achieved through extended component life, including increased engine and gearbox rebuild intervals, together with re-designed components and systems to reduce parts costs. Body panel design and fit have also been optimised which will not only minimise pit lane repair times but also aids weight distribution through the use of lighter components.

Increased levels of safety and refinement for the driver

Inside the cockpit, the 650S GT3 provides improved levels safety for the driver. Protection offered by the carbon fibre MonoCell chassis is further enhanced with the addition of an FIA-approved rollcage. Redesigned and lighter than that of the 12C GT3, the 650S GT3 rollcage provides a greater degree of driver comfort, with increased leg and headroom.

Another key area that has been optimised is the level of refinement, underlining the focus on endurance and driver engagement. As with its predecessor, the 650S GT3 is fitted with a bespoke motorsport digital dash display which sits behind the unique 650S GT3 steering wheel, inspired by the wheel design seen in the McLaren Mercedes Formula 1™ car. New to the 650S GT3 is a fully FIA-approved McLaren GT-developed race seat, fitted with a six-point race harness as standard. This seat offers increased levels of support and driver comfort through the use of bespoke moulded seat inserts.

The layout within the cockpit has been revised to make it even more driver-focused than previously. The seat is directly mounted to the chassis, and the steering wheel and all-new motorsport pedalbox are then adjustable to bring them closer to the driver. The centre console is also developed from the latest 12C GT3 interior, reducing complexity, and features a membrane-type switch panel for ease of use. In addition to this, improvements have been made to further optimise ventilation and driver cooling.

2015 McLaren 650S GT3 High Resolution Exterior
- image 557789

Award-winning technology, optimised cooling

The 650S GT3 is equipped with the latest generation of the award-winning, 3.8-litre McLaren V8 twin turbo ‘M838T’ engine. Race-prepared and including a McLaren-developed ECU offering increased functionality to incorporate turbo boost and transmission shift control, the engine is coupled to an all-new six-speed sequential motorsport transmission. The 650S GT3 produces around 500PS – the same power as the 12C GT3, which is controlled by the FIA’s Balance of Performance (BOP) regulations. Cooling is improved through larger 650S intakes within the front bumper and re-profiled side intakes. In addition to this, the gearbox oil cooler has been relocated, now incorporated into the larger side intakes, giving the rear of the car a cleaner, more aerodynamic flow.

Race tuned with increased grip

The 650S GT3 uses an all-new race-tuned suspension system with a 52mm wider track than the 12C GT3. The front suspension also allows the fitment of the latest generation larger diameter racing tyres . In conjunction with the optimised aerodynamic package, this provides increased levels of front-end grip and steering feel on turn-in. Newly designed forged aluminium wheels (front - 12.5” x 18”, rear – 13” x 18”) are held in place with a single wheel retaining nut on motorsport axles, while a revised hub bearing assembly and extended-life suspension components are another example of a simplified service item, and reduced maintenance costs.

2015 McLaren 650S GT3 High Resolution Exterior
- image 557790

Behind the new design eight-spoke wheels, and bringing the power, aerodynamics and downforce under control is a newly-developed braking system with monoblock six-piston callipers on the front, and four-piston on the rear, with ventilated discs (380 x 35mm front / 355 x 32mm rear).

Existing owners can upgrade

The 650S GT3 development programme has pulled significant data from the findings and lessons learned from the 12C GT3 programme. Testing of the 650S GT3 will continue throughout the summer with customer car production commencing in the autumn. Pricing for the 650S GT3 has been confirmed – £330,000 ex works, plus tax.

Existing owners of the 12C GT3 are also able to benefit from the updates and enhancements offered by the 650S GT3, due to the use of the shared chassis structure and award winning engine. This upgrade package further extends the life of existing 12C GT3 cars allowing them to continue racing competitively through a second GT racing life cycle. For many McLaren GT3 owners this allows them to race their existing car for an average of six seasons.

Around 15 examples of the 650S GT3 are planned to be produced and delivered for the start of the 2015 season. With the optional upgrade package for 12C GT3, this could see an additional 15 cars running the new design from next season.

Mike Flewitt, Chief Executive Officer, McLaren Automotive:

2015 McLaren 650S GT3 High Resolution Exterior
- image 557791

‘The McLaren 650S GT3 is to GT racing what the 650S is to McLaren Automotive, with the new car improving on all areas of a strong existing product, and making it more engaging at the same time. It shares the heart and soul of its road-going sibling with the same 3.8-litre twin turbo engine and the carbon fibre chassis, but turns things up to 11 in terms of aerodynamics. It is truly fit for purpose, but is now accessible to an even wider breadth of abilities and, as with the road car, it provides unprecedented levels of comfort, safety and driver engagement.’

Andrew Kirkaldy, Managing Director, McLaren GT:

‘The 650S GT3 is a natural progression of an already successful racer, but we have looked at all the different areas where we could possibly make even the slightest incremental improvement. The revised aerodynamic profile looks much more purposeful, and we have managed to incorporate increased levels of cooling without any detriment to performance. A big step forward has also been made in terms of servicing the car, which can be the difference between a race win and finishing off the podium, and the cost of running a car at a competitive level, and this becomes more important the longer and more demanding the event. By simplifying maintenance

and repair processes, and cutting down the time and costs involved, the 650S GT3 will be even more competitive at the longer endurance events with time required in the pitlane reduced to a minimum. ‘

‘Throughout the development programme, we have focused on making the 650S GT3 even more enjoyable and engaging to drive for the wide range of drivers that are competing in GT racing around the world. With a broader envelope of performance, which is easier to access, more drivers will be able to exploit the true potential of the 650S GT3. One example is with the wider track, which gives greater levels of grip and improves handling.’

2015 McLaren 650S GT3 High Resolution Exterior
- image 557792

Chris Goodwin, Chief Test Driver, McLaren Automotive:

‘This is a car that is improving on a race-winning formula, and is designed and built to offer even greater levels of driver involvement, but also to be easier to drive. This is a crucial factor in any racing car, but especially with long-distance and endurance racing, where drivers can double or even triple stint, where we compete on a huge variety of circuits and where weather and track conditions vary regularly throughout a race.

‘GT racing attracts a wide variety of drivers - from the best and most experienced professionals in the world to ambitious amateurs and young developing talents. If the car is easy to drive and gives good feedback as you approach and sometimes exceed the limit, the driver will be better able to drive consistently, error free and extract more out of the car lap after lap. This is key for professional race winner as much as it is for the amateur racers that are making up increasingly large proportions of the grids around the world. It is the result of continuous development, both in terms of the work carried out by the McLaren GT design and development team, but it also takes the learnings from the thousands of laps, from countless circuits across the globe which have been completed by the 12C GT3 with our highly-successful, race winning customer teams. Real-world data and feedback from the teams gives us a much clearer understanding of what the cars go through which no simulator can provide. As such, the 650S GT3 will be just as competitive in the right hands, but more forgiving for the less experienced drivers that are being attracted to the exciting GT3 championships around the world.

‘The 12C GT3 was the first iteration of a GT car from McLaren, and was, and still is competing and winning on a regular basis. The 650S GT3 is now our second generation model, and it is up against more established rivals, many of which are on to the third, or in some cases, fourth. Just as we face in the road car market. Despite this, McLaren is still the brand to beat.’

What’s in a number? 59 - a winning pedigree

2015 McLaren 650S GT3 High Resolution Exterior
- image 557793

The car unveiled carries the Goodwood Festival of Speed theme of ‘addicted to winning’, with its livery including the number 59. The number was carried by the now legendary McLaren F1 GTR chassis #01R at the 24 Hours of Le Mans in 1995, and claimed victory in the gruelling test of endurance on its debut – a feat that had never been achieved previously, and has not been repeated since. Deliveries of the 650S GT3 will commence from late 2014, and the competitive debut with customer teams in GT3-homologated series will start in 2015, 20 years on from the famous race victory.

View the full press release Hide press release
Press release
What do you think?
Show Comments
Car Finder: